mywiki x

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
=== Flash Xiaomi Mi Humi Sensors ===
[[XiaomiHumiFlash]]

=== Connect to tasmota via usb/serial ===

Make sure you have miniterm installed 'sudo apt install miniterm' 

Connect the device directly vis usb or a serial to usb converter

Enter `dmesg` too see which ttyUSB[X] device it is, where [X] is a number (probably 0)

Crank 'miniterm /dev/ttyUSB[X] 115200 -e' into the terminal.

Hack 'Status 11' into the terminal and see the wifi params.

If you need to reprogramn them prepare the following line in kate (or any other text editor):
<code>
Backlog SSID1 yourwifi1; Password1 yourpassword1; SSID2 yourwifi2; Password2 yourpassword2; MqttHost 192.168.2.5
</code>

Then copy and paste it into the miniterm and hit enter.

It should restart and connect to your wifi finally...



=== Build Tasmota from Scratch on linux ===
** Cli only / (no vscode needed) **

Look here but install python3-pip instead of python-pip on ubuntu >=20
https://tasmota.github.io/docs/PlatformIO-CLI/#download-the-tasmota-source-code
a backup is here [[installplatformio-copy|installplatformio-copy]]

Put this at the end of tasmota/user_config_override.h.
Fill in passwords and MQTT Server.

<code>
// !!! Remember that your changes GOES AT THE BOTTOM OF THIS FILE right before the last #endif !!!
*/


#undef  CFG_HOLDER
#define CFG_HOLDER        4723                  // [Reset 1] Change this value to load SECTION1 configuration parameters to flash

#define MODULE                 SONOFF_BASIC      // [Module] Select default module from tasmota_template.h

#undef MQTT_FULLTOPIC 
#define MQTT_FULLTOPIC         "%prefix%/%topic%/" // [FullTopic] Subscribe and Publish full topic name - Legacy topic
#undef MQTT_TOPIC
#define MQTT_TOPIC             "SONOFF/%06X"   // [Topic] unique MQTT device topic including (part of) device MAC address

// -- Setup your own Wifi settings  ---------------
#undef  STA_SSID1
#define STA_SSID1         "stystowlan2"             // [Ssid1] Wifi SSID

#undef  STA_PASS1
#define STA_PASS1         ""     // [Password1] Wifi password

// -- Setup your own Wifi settings  ---------------
#undef  STA_SSID2
#define STA_SSID2         "homebasket3"             // [Ssid1] Wifi SSID

#undef  STA_PASS2
#define STA_PASS2         ""     // [Password1] Wifi password

// -- Setup your own MQTT settings  ---------------
#undef  MQTT_HOST
#define MQTT_HOST         "192.168.0.18" // [MqttHost]



</code>


For typcial sonoff use this to compile and upload:
<code>platformio run -e tasmota --target upload --upload-port /dev/ttyUSB0
</code> 

For esp32 and bluetooth use this:
<code>platformio run -e tasmota32-bluetooth --target upload --upload-port /dev/ttyUSB0</code>
Or esptool
<code>esptool.py -p /dev/ttyUSB0 --chip esp32 --baud 921600 --before default_reset --after hard_reset write_flash -z --flash_mode dout --flash_size detect 0x0 tasmota32.bluetooth.bin
</code>

If compiler errors about missing dependcies show up delete your .platformio folder, which might contain files from previous platforms
mywiki x

User Tools

Site Tools

Page Tools
